Do you have any antivirus recomendations for Linux.

  • stravanasu@lemmy.sdf.org
    ·
    1 year ago

    Thank you for the advice!

    Firewall on Linux is something I still don't understand, and explanations found on Internet have always confused me. Do you happen to know some good tutorial to share? Or maybe one doesn't need to do anything at all in distros like Ubuntu?

    Regarding ssh: you only mean incoming ssh, right?

    • stravanasu@lemmy.sdf.org
      ·
      edit-2
      1 year ago

      @bushvin@pathfinder.social @toikpi@feddit.uk @hevov@discuss.tchncs.de @ChonkaLoo@lemmy.world @HotBoxghost2743@lemmy.ml @c1177johuk@lemmy.world (I'm surely forgetting someone, sorry)

      Thank you ALL for the great advice and guides! I'm writing from behind a laptop firewall now, and don't notice anything :) It was smoother than I expected. In the end I used UFW because it was already installed, but I'll take a look at firewalld too in some days! I don't have any incoming ssh connections (not a server), so I didn't need to worry about that :)

      Really great people here at Lemmy :)

    • hevov@discuss.tchncs.de
      ·
      1 year ago

      I don't think you need to configure your firewall. Firewalls are usualy used to block incomming connectings. Usualy a Firewall that blocks all incomming connections is already active on your modem/router. Adding exception to the modem/router Firewall usualy happen through port forwords.

    • bushvin@pathfinder.social
      ·
      1 year ago

      Yes, usually you configure your endpoint firewall to block incoming traffic, while allowing all outgoing.

      Unless you’re in a very secure zone, like DMZ’s.

    • bushvin@pathfinder.social
      ·
      1 year ago

      ebtables and iptables can be very complex. And I failed my 1st RHCE exam because of them. But once you learn, you will never unlearn, as they are quite beautifully crafted. You just need to get into the mindset of the people who wrote the tools…

      Look into firewalld It has a rather simplified cli interface: firewall-cmd

      The manpages will tell you a lot.

      firewall-cmd —add-service=ssh Will open the ports for your ssh daemon until you reload your firewall or reboot your system firewall-cmd —permanent —add-service=ssh Will open the ssh ports until you remove them

      firewall-cmd —list-all Will show you the current firewall config

    • Ghost@lemmy.ml
      ·
      1 year ago

      What don't you completely understand about Linux firewall? I don't mind helping you learn

      • stravanasu@lemmy.sdf.org
        ·
        1 year ago

        Thank you everyone, also @bushvin@pathfinder.social @toikpi@feddit.uk.

        For example, if I open my settings (I'm on Ubuntu+KDE) I don't see any firewall settings to configure. So I expect this is automatically done by the OS, but maybe I'm wrong. A bit surprised that the system itself doesn't recommend using a firewall, to be honest.

        Many firewall tutorials start speaking about "your server". Then I wonder: is this really for me? I don't have a server. Or do I?

        I now see that the tutorial from @toikpi@feddit.uk gives a better explanation, cheers! So I see it's good to have a firewall simply because one connects to public wifis from time to time.

        I see that both UFW and firewalld are recommended... is it basically OK whichever I choose?

        • bushvin@pathfinder.social
          ·
          1 year ago

          I see that both UFW and firewalld are recommended... is it basically OK whichever I choose?

          Yes. Whichever works for you should be fine. In the end you should be able to manage it

        • Ghost@lemmy.ml
          ·
          edit-2
          1 year ago

          The main one everybody uses at least from my knowledge and from what I've used over the last 13 years is UFW. That is what you want to use.

          A firewall is very important not just for being on public Wi-Fi connections. A firewall is your extra layer of protection

          I don't know what Distro you run. But it's almost the same for each one

          https://www.digitalocean.com/community/tutorials/how-to-set-up-a-firewall-with-ufw-on-ubuntu-20-04

          UFW is installed by default on Ubuntu. If it has been uninstalled for some reason, you can install it with sudo apt install ufw.

          Using IPv6

          sudo nano /etc/default/ufw

          That command should come back with this

          IPV6=yes

          Save and close the file. Now, when UFW is enabled, it will be configured to write both IPv4 and IPv6 firewall rules. However, before enabling UFW, we will want to ensure that your firewall is configured to allow you to connect via SSH. Let’s start with setting the default policies.

          Setting up default policies

          sudo ufw default deny incoming sudo ufw default allow outgoing

          These commands set the defaults to deny incoming and allow outgoing connections. These firewall defaults alone might suffice for a personal computer, but servers typically need to respond to incoming requests from outside users. We’ll look into that next.

          To configure your server to allow incoming SSH connections, you can use this command:

          sudo ufw allow ssh
          

          This will create firewall rules that will allow all connections on port 22, which is the port that the SSH daemon listens on by default. UFW knows what port allow ssh means because it’s listed as a service in the /etc/services file.

          However, we can actually write the equivalent rule by specifying the port instead of the service name. For example, this command works the same as the one above:

          sudo ufw allow 22
          

          If you configured your SSH daemon to use a different port, you will have to specify the appropriate port. For example, if your SSH server is listening on port 2222, you can use this command to allow connections on that port:

          sudo ufw allow 2222
          

          To enable UFW, use this command:

          sudo ufw enable
          
          • bushvin@pathfinder.social
            ·
            edit-2
            1 year ago

            The main one everybody uses at least from my knowledge and from what I've used over the last 13 years is UFW. That is what you want to use.

            I could easily say that for firewalld… 😃

            Ufw is typically available/pre-installed with Debian based systems (Debian, Ubuntu, zzz), while Firewalld is typically available on Red Hat Enterprise Linux and derivates (Fedora, CentOS, Rocky, …)

            But it boils down to what you prefer, really.

            • Ghost@lemmy.ml
              ·
              1 year ago

              I know all this already. But I also use arch and have been for the last 6+ years and I use ufw lol